Sunamco
Metal coating finishing products.

Series 350

350 Line is an air dry enamel with good anti corrosive properties.

Download as PDF

Reminder

Application viscosity :

Conventional spray : 20-35 sec FC#4

Airless and airmix spray : 40-50 sec FC#4


Properties
  • Good adhesion
  • Good flexibility
  • Good durability
  • Good application characteristics
  • It can be applied over old paint without lifting olf paint
  • Low VOC
Advantages
  • Ofeered in wide variety of colors
Technical Information
Gloss 90°+
Reducer 100-022
Shelf life 8-10 months (Unopened)
Theoretical solids content 50-60 (P/P) ; 42-46 (V/V)
Coverage (Theoretical calculation) 17-19 m²/L for 25 µm dry film ; 180-200 ft²/L for 1 mil of dry film
Recommended dry film thickness 3-4 mils dry
Drying time at 77ºF or 25ºC at 40% relative humidi... Dust free 60-90 minutes ; Ready to handle 8-10 hours ; Deep dry 72 hours
Uses
  • Farm and forestry equipment
Recommended Topcoat

It is normally direct to metal.

Other series are available. For more info0rmation, please communicate with your sales representative.

Surface preparation

-Coated surface must be clean, dry and free from impurities, soluble salt, oil, grease, wax, and rust.

-We recommend to use a minimum metal.

-Preparation such as SSPC-SP-2 or SSPC-SP3

-Substrate temperature must be higher by at least 3°C than dew point temperature in order to prevent condensation.

Application

-Mix well before application

For conventional equipment:

-Reduce the material with thinner 100-022 to a viscosity of 20-25 sec FC#4 before application.

-Approximate gun pressure of 45 PSI(approximately)and tank pressure of 18 PSI at the tank.

 

For airless and airmix equipment:

-Reduce the material with thinner to a viscosity of 40-50 sec FC#4 before application. (8 parts of paint for 1 part of thinner)

-The pressure at the pump 1000-1200 PSI.

 

Consult your local sales representative for information about the application.

Precaution

-Once work is done, do not leave paint in hoses, guns or spray equipment.Equipment should be thoroughly cleaned with Sunamco Sunaclean 100-113

-For drying period exceeding 72 hours, a light sanding si highly recommended for best inter-layer adhesion.

-Make sure you completely cover the profile in order to avoid pin rust.

 TEST:

Due to several varieties of substrates, surface preparation methods, application methods, and environment, the user must verify the entire system and verify adhesion and compatibility based upon environment before starting the production.

 

N.B. To make adhesion, hardness, flexibility, impact test, or any other test, it is recommended to wait 14 daysat 25ºC (68ºF) and 50% humidity to enable the chemical reaction to be completed. If conditions are not fits outlined, the reaction time could be longer.

Restrictions

- Do not apply at temperatures below 10oC or 50o F otherwise drying and the hardness will be affected.

Caution

- Make sure to have good ventilation during application and drying

-Please consult material safety data sheet prior to use.

Limitation of liability

This information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application which are not known or under our control, Sunamco cannot make any warranties as to the end result. 






shadow

Login

Please contact us if you want to obtain a username and password to see the detailed technical information about our products.
Username
Password

Careers

Sunamco offers outstanding professional opportunities. Our people are our greatest asset and work in a stimulating and respectful environment. Sunamco’s success is mainly due to the professionalism and enthusiasm of our team members.

Click here to learn more

Sunamco

Located in Centre-du-Québec, Sunamco is a young company specializing in industrial finishes for metal coating.

360, 6e Rue
Daveluyville, Qc, Canada, G0Z 1C0
819-367-4080 1-866-815-4080

shadow