Sunamco
Metal coating finishing products.

Series 200

The series #200 is a fast drying D.T.M (direct to metal) enamel formulated for outdoor uses and for direct to metal applications.

Download as PDF

Reminder

Application viscosity : 20-35 sec.

Usual thinner : 100-018

Hardener (optional) : 200-000B

Ratio : 9:1

 


Properties
  • Good direct on metal adherence.
  • Fast ambient temperature drying.
Advantages
  • Offered in wide variety of colors.
  • Offered in different gloss %.
  • Quick drying.
Technical Information
Gloss On request
Reducer 100-018
Shelf life 12 months
Theoretical solids content 40 – 47 (V/V); 42-57 (P/P)
Coverage (Theoretical calculation) 16 – 19 m2/L for 25 µm dry film, 173 – 199 ft2/L for 1 mil of dry film
Recommended dry film thickness 2 mils sec
Drying time at 77ºF or 25ºC at 40% relative humidi... Dust free 10-15 minutes. Ready to handle 20-30 minutes. Deep dry 48 hours
Uses
  • Small parts
Recommended Topcoat

Direct to metal (DTM)

 

Other series are available. For more info0rmation, please communicate with your sales representative.

Surface preparation
  • Coated surface must be clean, dry and free from impurities, soluble salt, oil, grease, wax, and rust.
  • We recommend using commercial preparation standards SSPC-SP-2 or SSPC-SP3.
  • Commercial standard SSPC-SP-6, sandblasting, would be much more appropriate and strongly recommended for better corrosion resistance.
  • Substrate temperature must be higher by at least 3°C than dew point temperature in order to prevent condensation.
Application
  • Mix well before application.
  • Application either sprayed or brushed.

 

For conventional equipment:

  • Reduce the material with thinner to a viscosity of 20-25 sec FC#4 before application.
  • Approximate gun pressure of 45 lbs/po2 and tank pressure of 18 lbs/po2.

 

For "airless" equipment:

  • Reduce the material with thinner to a viscosity of 25-35 sec FC#4 before application.

Consult your local sales representative for information about the application.

Precaution
  • Once work is done, do not leave paint in hoses, guns or spray equipment.
  • Equipment should be thoroughly cleaned with Sunamco Sunaclean 100-113.
  • For drying period exceeding 24 hours, a light sanding si highly recommended for best inter-layer adhesion.
  • Make sure you completely cover the profile in order to avoid pin rust.

TEST:

Due to several varieties of substrates, surface preparation methods, application methods, and environment, the user must verify the entire system and verify adhesion and compatibility based upon environment before starting the production.

N.B. To make adhesion, hardness, flexibility, impact test, or any other test, it is recommended to wait 7 daysat 25ºC (68ºF) and 50% humidity to enable the chemical reaction to be completed. If conditions are not fits outlined, the reaction time could be longer.

Restrictions

Do not apply at temperatures below 10oC or 50o F otherwise drying and the hardness will be affected.

Caution

This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s) and should not be used without reference to the Material Safety Data Sheet (MSDS).

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult Société Chimique Sunamco Inc. for further advice.

Limitation of liability

This information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application which are not known or under our control, Sunamco cannot make any warranties as to the end result.






shadow

Login

Please contact us if you want to obtain a username and password to see the detailed technical information about our products.
Username
Password

Careers

Sunamco offers outstanding professional opportunities. Our people are our greatest asset and work in a stimulating and respectful environment. Sunamco’s success is mainly due to the professionalism and enthusiasm of our team members.

Click here to learn more

Sunamco

Located in Centre-du-Québec, Sunamco is a young company specializing in industrial finishes for metal coating.

360, 6e Rue
Daveluyville, Qc, Canada, G0Z 1C0
819-367-4080 1-866-815-4080

shadow