Sunamco
Metal coating finishing products.

Series 300

300 Line is an air dry D.T.M (direct to metal) enamel with good anti corrosive properties.

Download as PDF

Reminder

Application viscosity : 20-35 sec.


Properties
  • Good adhesion to metal
  • Good flexibility.
  • Good durability.
  • Good application characteristics.
  • It can be applied over old paint without lifting old paint.
Advantages
  • Offered in wide variety of colors.
  • Offered in different gloss %.
  • Quick drying.
  • Anti-lifting properties
Technical Information
Gloss On request
Reducer 100-022
Shelf life 8-10 months (Unopened)
Theoretical solids content 41 - 48 (V/V) ; 48 - 62 (P/P)
Coverage (Theoretical calculation) 16 – 19 m2/L for 25 µm dry film. 179 – 203 ft2/L for 1 mil of dry film
Recommended dry film thickness 3-4 mils dry
Drying time at 77ºF or 25ºC at 40% relative humidi... Dust free 60-90 minutes. Ready to handle 4-5 hours. Deep dry 48 hours.
Uses
  • Farm and forestry equipment.
Recommended Topcoat

It is normally direct to metal.

 

Other series are available. For more info0rmation, please communicate with your sales representative.

Surface preparation
  • Coated surface must be clean, dry and free from impurities, soluble salt, oil, grease, wax, and rust.
  • We recommend to use a minimum metal.
  • Preparation such as SSPC-SP-2 or SSPC-SP3.
  • Substrate temperature must be higher by at least 3°C than dew point temperature in order to prevent condensation.
Application
  • Mix well before application

 

For conventional equipment:

  • Reduce the material with thinner to a viscosity of 20-25 sec FC#4 before application.
  • Approximate gun pressure of 45 PSI(approximately)and tank pressure of 18 PSI at the tank.

 

For "airless" equipment:

  • Reduce the material with thinner to a viscosity of 25-35 sec FC#4 before application.
  • The pressure at the pump 1000-1200 PSI.

Consult your local sales representative for information about the application.

Precaution
  • Once work is done, do not leave paint in hoses, guns or spray equipment.
  • Equipment should be thoroughly cleaned with Sunamco Sunaclean 100-113.
  • For drying period exceeding 24 hours, a light sanding si highly recommended for best inter-layer adhesion.
  • Make sure you completely cover the profile in order to avoid pin rust.

TEST:

Due to several varieties of substrates, surface preparation methods, application methods, and environment, the user must verify the entire system and verify adhesion and compatibility based upon environment before starting the production.

N.B. To make adhesion, hardness, flexibility, impact test, or any other test, it is recommended to wait 7 daysat 25ºC (68ºF) and 50% humidity to enable the chemical reaction to be completed. If conditions are not fits outlined, the reaction time could be longer.

Restrictions

Do not apply at temperatures below 10oC or 50o F otherwise drying and the hardness will be affected.

Caution

This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s) and should not be used without reference to the Material Safety Data Sheet (MSDS).

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult Société Chimique Sunamco Inc. for further advice

Limitation of liability

This information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application which are not known or under our control, Sunamco cannot make any warranties as to the end result.






shadow

Login

Please contact us if you want to obtain a username and password to see the detailed technical information about our products.
Username
Password

Careers

Sunamco offers outstanding professional opportunities. Our people are our greatest asset and work in a stimulating and respectful environment. Sunamco’s success is mainly due to the professionalism and enthusiasm of our team members.

Click here to learn more

Sunamco

Located in Centre-du-Québec, Sunamco is a young company specializing in industrial finishes for metal coating.

360, 6e Rue
Daveluyville, Qc, Canada, G0Z 1C0
819-367-4080 1-866-815-4080

shadow