Sunamco
Metal coating finishing products.

Sunaguard 7000

SUNAGUARD #7000 is a two component aliphatic polyurethane with high gloss. This product is designed to offer an outstanding exterior durability, a very aesthetic finish and an excellent color retention.

Download as PDF

Reminder

HARDENER                  7050B

RATIO                             2:1:10%

REDUCER (regular)    100-118

REDUCER (slow)        100-007

Drying Time(between layers)    20-25 min

 

                                 DRYING TIME (between layers)     20-25 min


Properties
  • Excellent aesthetic finish (wet look)
  • Easy to apply
  • Excellent exterior durability
  • Dry film is flexible while providing very good hardness
  • Outstanding gloss and color retention
  • Very good distinction of image (D.O.I.)
Advantages
  • Very good distinction of image
  • Very good chemical resistance
  • Excellent hiding properties
  • High solid product
  • Easy to apply
Technical Information
Gloss 90º +
Pot life of mixed product (A+B) 4-6 hours
Reducer 100-118
Retarder 100-007
Shelf life 12 months
Theoretical solids content 64 - 73 (W/W), 59 - 63 (V/V)
Coverage (Theoretical calculation) 24 - 25 Sq M/L for 25 µm dry film, (Theoretical calculation) 250 - 267 ft²/L for 1 mil of dry film
Recommended dry film thickness 2 to 3 dry mils
Drying time at 77ºF or 25ºC at 40% relative humidi... Dust free 1 hour, ready to handle 12 hours, dry hard 72 hours
Uses
  • Commercial vehicles                            
  • Heavy duty equipment
  • Wagons                                                      
  • Farm equipment   
  • Industrial equipment                               
  • Truck cabs
  • Trailers                                                     
  • Rolling stock
Recommended Topcoat

SUNAPRIME                           Series #6400 Ultra fast to topcoat

SUNAPRIME                           Series #603 Fast drying

SUNAPRIME                           Series #611 High solid/volume

SUNAPRIME                           Series #612 Sanding properties

Surface preparation

Surfaces should be clean, dry and free of dirt, rust, oil, soluble salt or water, grease, wax, loose paint and any other contaminants.

We recommend to use minimum commercial preparation standards as SSPC-SP6 or SSPC-SP3

SSPC-SP6 sandblasting standard would be much more appropriate and strongly recommended for better corrosion resistance.

Surface temperature must be at least 3oC higher to the dew point temperature in order to avoid condensation.

Application

Hardener  7050B

Mix 2 parts by volume of Sunaguard (part A) and 1 part of 7050B.

A finishing type nozzle is recommended to obtain an even glossy finish.

 

For conventional equipment:

Reduce the material with thinner to a viscosity of 20-30 sec FC#4 before

applying.

Pressure at gun should be approximately 30-50 PSI and 9-12 PSI in pressure tank.

Precaution

Do not leave the paint in the hose, guns and pump. The equipment has to be well cleaned with Sunamco cleaning thinner 100-113

After 24 hours drying time, scuff sanding is required before applying an other coat in order to obtain a better intercoat adhesion.

 TEST:

Due to the wide variety of substrates, surface preparation methods, application methods, and environment, users should test the complete system for adhesion and compatibility under their conditions prior starting production.

 N.B. To make adhesion, hardness, flexibility, impact test, or any other test, it is recommended to wait 7 days at 20ºC (68ºF) and 50% humidity to enable the chemical reaction to be completed. If conditions are not fits outlined, the reaction time could be longer.

Restrictions

 Do not apply at temperatures below 10oC or 50o F otherwise drying and the hardness will be affected.

Caution

This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s) and should not be used without reference to the Material Safety Data Sheet (MSDS).

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult Société Chimique Sunamco Inc. for further advice.

Limitation of liability

This information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application which are not known or under our control, Sunamco cannot make any warranties as to the end result






shadow

Login

Please contact us if you want to obtain a username and password to see the detailed technical information about our products.
Username
Password

Careers

Sunamco offers outstanding professional opportunities. Our people are our greatest asset and work in a stimulating and respectful environment. Sunamco’s success is mainly due to the professionalism and enthusiasm of our team members.

Click here to learn more

Sunamco

Located in Centre-du-Québec, Sunamco is a young company specializing in industrial finishes for metal coating.

360, 6e Rue
Daveluyville, Qc, Canada, G0Z 1C0
819-367-4080 1-866-815-4080

shadow