Sunamco
Metal coating finishing products.

Sunaprime 611

SUNAPRIME #611 is a two-component epoxy primer formulated to fill the sandblast profile in one coat and also for good sanding properties.

Download as PDF

Reminder

Hardener: 611-000B (Regular)

                   611-001B (Increase resistance to sagging)

 Ratio: 4:1  Reducer: 100-117  Retarder: 100-118

Dry time: Ready to topcoat 4 hours


Properties
  • High spreading rate
  • Very good flexibility
  • Excellent adhesion to steel, treated aluminium, satin galvanized
  • Very good impact resistance
  • Very good abrasion resistance
  • Very good anticorrosive properties
  • Very good sag resistance
  • ASTM B117: 1000 hours
Advantages
  • High percentage of solids by volume
  • Any color can be developed on request.
Technical Information
Gloss 65°+
Pot life of mixed product (A+B) 6 hours
Reducer 100-117
Retarder 100-118
Shelf life 12 months (subject to re-inspection thereafter)
Theoretical solids content 63-72 (P/P) ; 53-60 (V/V)
Coverage (Theoretical calculation) 25-29 Sq M/L for 25 µm dry film ; 274-309 Sq ft/L for 1 mil of dry film
Recommended dry film thickness 3-4 dry mil
Drying time at 77ºF or 25ºC at 40% relative humidi... Dust free : 45-60 minutes ; Ready to handle 60-90 minutes ; Ready to topcoat 4 hours
Uses
  • Truck frame
  •  Wagons
  • Snow blowers
  •  Trailers
  •  Farm equipment
  • Industrial equipment
Recommended Topcoat
  • SUNAGUARD 7000
  • SUNATHANE 745
  • SUNAVIT 788

 

For more information, please contact your representative

Surface preparation
  • Surface should be clean, dry, and free of dirt, rust, oil, soluble salt or water, grease, wax, loose paint, and any other contaminants.
  • We recommend a minimum commercial preparation such as SSPC-SP-2 or SSPC-SP3.
  • SSPC-SP-6  standard sandblast would be much more appropriate and strongly recommended for better corrosion resistance.
  • Surface temperature must be at least 3oC higher to the dew point temperature in order to avoid condensation.
Application
  • Hardener: 611-000B (regular) & 611-001B (anti-sagg)
  • Mix 4 parts by volume of A and 1 part by volume of B.

IMPORTANT: Mix mechanically in order to obtain a homogeneous product

METHOD:

  • Conventional air spray
  • Airless, air assisted, air mix.
  • Electrostatic version (contact your representative).
  • Paint brush for hardly accessible places.

 

For conventional equipment:

  • Reduce the material with thinner to a viscosity of 20-25 sec FC#4 before applying.
  • Pressure at gun should be approximately 40-50 PSI and 10-15 PSI in pressure tank.

 

For "airless" equipment:

  • Reduce the material with thinner to a viscosity of 25-35 sec FC#4 before applying.

Consult your local sales representative for information about the application.

Precaution
  • Do not leave the paint in the hose, guns and pump. The equipment has to be well cleaned with Sunamco cleaning thinner Sunaclean 100-113.
  • For drying time exceeding 24 hours we recommend a light sanding for a better inter-coat adhesion.
  • Make sure you complete the profile sandblasting in order to avoid surface rust caused by an angular profile.

TEST:

Due to the wide variety of substrates, surface preparation methods, application methods, and environment, users should test the complete system for adhesion and compatibility under their conditions prior to starting their production.

N.B. To make adhesion, hardness, flexibility, impact test, or any other test, it is recommended to wait 7 daysat 25ºC (68ºF) and 50% humidity to enable the chemical reaction to be completed. If conditions are not fits outlined, the reaction time could be longer.

Restrictions
  • Do not apply at temperatures below 10oC or 50o F otherwise drying and the hardness will be affected.
  • As with most epoxy coatings, when there is no topcoat, the 603 line may chalk or discolour when exposed to ultraviolet outside light.  On the other hand, this does not affect the anticorrosive properties of this product.
Caution
  • This product must be used in a well ventilated area.
  • Before using this product, please consult MSDS label and Technical Data Sheet.
Limitation of liability

This information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application which are not known or under our control, Sunamco cannot make any warranties as to the end result.






shadow

Login

Please contact us if you want to obtain a username and password to see the detailed technical information about our products.
Username
Password

Careers

Sunamco offers outstanding professional opportunities. Our people are our greatest asset and work in a stimulating and respectful environment. Sunamco’s success is mainly due to the professionalism and enthusiasm of our team members.

Click here to learn more

Sunamco

Located in Centre-du-Québec, Sunamco is a young company specializing in industrial finishes for metal coating.

360, 6e Rue
Daveluyville, Qc, Canada, G0Z 1C0
819-367-4080 1-866-815-4080

shadow