Sunamco
Metal coating finishing products.

Series 650

The series #650 is  a one component phenolic primer for metal designed to provide enhances corrosion resistance.

Download as PDF

Reminder

Reducer: 100-118. Viscosity: 20-35 sec.


Properties
  • Fast drying at room temperature.
  • Easy to use
  • Increase corrosion resistance
  • Very good adherence
  • Good flexibility
Advantages
  • Easy to use.
  • Good corrosion resistance
  • Fast drying
Technical Information
Gloss matt
Reducer 100-018
Shelf life 8 months
Theoretical solids content 65 – 73 (P/P). 53– 58 (V/V).
Coverage (Theoretical calculation) 21 – 23 m2/L for 25 µm dry film. 225 – 246 ft2/L for 1 mil of dry film thickness.
Recommended dry film thickness 2 dry mils
Drying time at 77ºF or 25ºC at 40% relative humidi... Dust free 10-15 min. Ready to handle 20-35 minutes. Dry hard 60 minutes.
Uses
  • Small trailers
  • Industrial equipment
  • Metal structures
  • Farm equipment
  • Construction equipment
Recommended Topcoat

RECOMMANDED FINISHED:

  • Series #200 Fast drying enamel.
  • Series #300 Conventional enamel.

 

For more information, please contact your representative.

Surface preparation
  • Surface should be clean, dry, and free of dirt, rust, oil, soluble salt or water, grease, wax, loose paint, and any other contaminants.
  • We recommend using a minimum of preparation the commercial directive SSPC-SP-2 and SSPC-SP3.
  • The directive SSPC-SP-6 concern the sandblast. It will be appropriate and highly suggested for a better corrosion resistance.
  • The surface temperature must be at least 3°C higher to the temperature of the dew point to avoid condensation.
Application

Methods:

  • Paint brush
  • Roller
  • Spray

 

For conventional equipment:

  • Reduce the material with thinner to a viscosity of 20-25 sec FC#4 before applying.
  • Pressure at gun should be approximately 40 pounds/in2 and 18 pounds/in2 at the tank.

 

For "airless" equipment:

  • -Reduce the material with thinner to a viscosity of 25-35 sec on a FC#4 before applying.
  • The pump pressure with assorted air is 1000 to 1200 pounds/in2
Precaution
  • Do not leave the paint in the hose, guns and pump. The equipment has to be well cleaned with Sunamco cleaning thinner 100-128.
  • After 24 hours drying time, it is recommended to scuff sand before applying and other coat in order to obtain a better inter-coat adhesion.

TEST:

Due to the wide variety of substrates, surface preparation methods, application methods, and environment, users should test the complete system for adhesion and compatibility under their conditions prior to starting their production.

N.B. To make adhesion, hardness, flexibility, impact test, or any other test, it is recommended to wait 7 daysat 20ºC (68ºF) and 50% humidity to enable the chemical reaction to be completed. If conditions are not fits outlined, the reaction time could be longer.

Restrictions

Do not apply at temperatures below 10oC or 50o F otherwise drying and the hardness will be affected.

Caution

This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s) and should not be used without reference to the Material Safety Data Sheet (MSDS).

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult Société Chimique Sunamco Inc. for further advice.

Limitation of liability

This information, rating, and options stated here pertain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application which are not known or under our control, Sunamco cannot make any warranties as to the end result.






shadow

Login

Please contact us if you want to obtain a username and password to see the detailed technical information about our products.
Username
Password

Careers

Sunamco offers outstanding professional opportunities. Our people are our greatest asset and work in a stimulating and respectful environment. Sunamco’s success is mainly due to the professionalism and enthusiasm of our team members.

Click here to learn more

Sunamco

Located in Centre-du-Québec, Sunamco is a young company specializing in industrial finishes for metal coating.

360, 6e Rue
Daveluyville, Qc, Canada, G0Z 1C0
819-367-4080 1-866-815-4080

shadow